2002
Safety Standards
Although thermography has gained wide acceptance for use in P/PM, Condition Monitoring and Forensics, thermographers often are unaware of the existence of published safety standards regarding infrared inspections.
The following is a partial list of currently distributed safety standards along with the organizations who publish them. Contact these organizations directly to obtain copies.
- National Fire Protection Association, Quincy MA
- NFPA 70E Standard For Electrical Safety Requirements for Employee
Workplaces - Occupational Safety and Health Administration
- 29 CFR Part 1910 Occupational Safety and Health Standards for General
Industry - 29 CFR Part 1926 Occupational Safety and Health Standards for General
Construction
It should be noted that many workers (miners, transportation, many federal workers) are exempt from OSHA standards; however, there are often agencies similar to OSHA that publish applicable standards for these workers.
Infrared Inspections are often performed in hazardous environments. Safely conducting an infrared inspection should be of paramount importance for all involved. Prior to beginning an infrared inspection, a thermographer must be aware of which safety standards apply to his/her work.
The Infraspection Institute Level 3 Certified Infrared Thermographer covers thermographer safety and applicable standards in depth. For more information, contact Infraspection Institute at 609-239-4788 or online at www.infraspection.com
Performance Standards
Performance Standards and Specifications for Thermography
Although thermography has gained wide acceptance for use in P/PM, Condition Monitoring and Forensics, thermographers often are unaware of the existence of published standards and specifications regarding infrared inspections.
The following is a partial list of currently distributed performance standards and specs along with the organizations who publish them. Contact these organizations directly to obtain copies.
- American Society for Testing and Materials, West Conshohocken, PA
- ASTM C 1060-97 Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
- ASTM C-1153-97 Practice for the Location of Wet Insulation in Roofing Systems Using Infrared Imaging
- ASTM E 1316-97 Terminology for Nondestructive Examinations
- ASTM E 1862-97 Standard Test Methods for Measuring and Compensating for Reflected Temperature Using Infrared Imaging Radiometers
- ASTM E 1933-97 Standard Test Methods for Measuring and Compensating for Emissivity Infrared Imaging Radiometers
- ASTM E 1934-97 Standard Guide for Examining Electrical and Mechanical Equipment with Infrared Thermography
- Infraspection Institute, Burlington, NJ
- Guidelines for Infrared Inspection of Building Envelopes and Insulated Roofs
- Guideline for Measuring Distance/Target Size Values for Quantitative Thermal Imaging Cameras
- Guideline for Measuring and Compensating for Reflected Temperature, Emittance and Transmittance
- Guidelines for Infrared Inspection of Electrical and Mechanical Systems
- International Electrical Testing Association, Morrison, CO
- Acceptance Testing Specifications for Electrical Power Distribution Equipment and Systems
- Maintenance Testing Specifications for Electrical Power Distribution Equipment and Systems
- National Fire Protection Association, Quincy MA
- NFPA 70B Recommended Practice for Electrical Equipment Maintenance
Proper conduct of an infrared inspection and interpretation of data require thorough training and certification by a recognized training agency. For more information on training and certification, contact Infraspection Institute at 609-239-4788 or online at www.infraspection.com
Proper Spectral Response
Choosing the proper equipment for an infrared inspection is of paramount importance when performing an infrared inspection.
Each model of infrared imaging system has many unique operating characteristics which must be considered before a project is undertaken. Of these, perhaps the most important is spectral response.
Spectral response for an imager generally falls into two categories: 2-5 microns (near infrared) or 8-14 microns (far infrared). Because spectral response can limit one’s ability to perform certain types of inspections, it is critical that a thermographer understand how spectral response can affect his/her work.
Below are some generally recommended spectral responses for different types of P/PM applications.
Application | 2-5 microns | 8-14 microns |
Indoor electrical systems |
X
|
X
|
Outdoor electrical systems |
X
|
|
High temperature targets |
X
|
|
Highly reflective targets |
X
|
|
Boiler/heater tubes – gas fired |
X
|
|
Long distance imaging |
X
|
|
Smooth surfaced roofs |
X
|
|
Gravel surfaced roofs |
X
|
X
|
Glass |
X
|
|
Plastics |
X
|
Proper conduct of an infrared inspection and interpretation of data require thorough training and certification by a recognized training agency. For more information on training and certification, contact Infraspection Institute at 609-239-4788 or online at www.infraspection.com
Inspecting Retrofitted Roofs
If your roof has been retrofitted with a new roof installed over an existing one, it is imperative that you test the roofing system for water infiltration at least annually. With limited opportunity for egress, water entering the upper roof of a retrofitted system can cause widespread damage in a very short period of time. To make matters worse, there is usually no visual evidence of this type of a leak from inside of the building.
Performed in conjunction with regular visual inspections of your roof, infrared inspections of low slope roofs are a very cost effective way of tracking the overall health of your facility’s roofing system. Locating leaking areas while they are small allows them to be addressed before they can spread. Additionally, moisture trapped within a roofing system almost never dries out and can cause premature failure of roofing felts, adhesives, fasteners, and the roof deck.
Whether you choose to have an in-house thermography team or an outside contractor perform the inspection, make certain that the Thermographer is Certified and experienced. Since an infrared imager cannot confirm moisture presence, all infrared data must be verified by invasive testing as well.
Before the onset of seasonably colder, now is the time to make sure your roof is ready to handle the winter.
Outdoor Substation Arrestors
Infrared inspections of lightning arrestors are primarily qualitative in nature. As such, thermographers should compare similar arrestors to one another and note any that are inexplicably warm.
Properly functioning lightning arrestors should be uniform in temperature and close to ambient air temperature if they have not undergone recent solar loading. Individual arrestors should not have any pronounced hot spots across them.
Because arrestors usually have a glazed porcelain surface, infrared inspections are best accomplished using a short wave (3-5 micron) imager. Working on cloudy days or at night will help to eliminate solar loading. When performing your inspection, don’t forget to check grounding connections for hot spots as well.
Saving Thermal Images
Many of today’s modern thermal imagers currently use PC cards to store thermal and/or daylight images. For many thermal imagers, infrared images can be stored in either 8 or 12 bit formats. The size of the stored images is user-defined and is controlled through the onboard firmware in the thermal imager.
Saving thermal images in 12 bit format allows the thermal image to be recalled at any time and post processed for level and gain within the imager or through the manufacturer’s proprietary software. It should be noted that 12 bit images tend to be quite large and if loaded to a PC will tend to fill a hard drive quickly.
Storing images in 8 bit format also allows images to be recalled at any time; however, these images cannot be adjusted for level and gain. Utilizing this smaller image file size not only saves hard drive space but also prohibits anyone from tampering with the original image settings.
Thermographers who distribute electronic copies of reports with 12 bit images should be aware that many manufacturers now offer very powerful freeware via the internet. Because this software can allow an untrained persons to post process report images, you should carefully consider which image format you distribute. Having an inexperienced person post process infrared images can have disastrous results if they do not understand the art and science of infrared temperature measurement.
For best results we recommend that only certified, experienced thermographers interpret temperature data from an infrared inspection.
Conveyor Bearings
If your facility utilizes conveyor systems for moving product, you may be able to use your thermal imager to locate defective bearings.
Many conveyor systems utilize a large number of rolling element bearings to support rollers or conveyor belting. Depending upon the size of the facility, a conveyor system may contain thousands of rolling element bearings. Due to the vast number of bearings, inspecting them can be an enormous and time consuming task.
Because bearing wear is usually accompanied by a rise in temperature prior to failure, infrared imaging can be used to detect overheating bearings. The infrared inspection is performed by comparing similar bearings under similar load. Bearings appearing inexplicably warm can be noted for further investigation.
When performing your infrared inspection, bearings should be operating at normal speed and you must have line-of-sight access to the subject bearings. Since the infrared inspection is performed from ground level without special preparation, the inspection can be performed quickly.
When performed by an experienced, certified thermographer, infrared inspections can provide a cost effective method for helping to eliminate unexpected failures and improving your production uptime.
Protecting Your Viewfinder
Have you ever seen what magnified sunlight can do to an insect? Similar damage can occur to your infrared camera if you are not careful.
Many infrared imagers utilize monocular eyepieces as monitor screens. When working outdoors, the LCD monitor display can be severly damaged or destroyed if sunlight enters the viewfinder through the magnifying lens of the viewer assembly. If the sunlight is strong enough and at the appropriate angle, the focused solar energy can melt a hole in the LCD screen in just a few seconds.
Always protect your eyepiece by shading or covering it when working outdoors to avoid allowing sunlight to enter the viewfinder. Doing so may prevent you from having to replace a costly eyepiece.
September 03, 2002
Sponsored by:
Cleaning IR Lenses
Always be sure to follow manufacturers instructions when cleaning infrared lenses and optics.
Lenses and optics are an integral part of any infrared imaging system. Most infrared optics are coated with special anti-reflective coatings to maximize the transmission of infrared energy to the system’s infrared detector. For imaging radiometers, each lens is individually calibrated to the imager.
Improperly cleaning a lens or coated optical element can cause the anti-reflective coating to be damaged thereby changing the transmittance of the lens and the measurement accuracy of the system. If the coating is sufficiently damaged, a costly lens replacement and system recalibration may be required. This recalibration would require sending your imager back to the manufacturer incurring up to several weeks of downtime for your imager.
September 07, 2002
Sponsored by:
Verifying Roof Data
When performing an infrared inspection of low slope roofs, it is imperative to verify thermal data with destructive testing. While infrared imagers can detect temperature changes associated with missing and damaged insulation, they cannot ascertain the cause of the thermal image.
Core sampling or invasive moisture meter readings are the only known methodologies for accurately determining moisture content. Coupling invasive verification with thermal imaging not only improves accuracy of the inspection but also is required by ASTM Standard C1153.
September 16, 2002
Sponsored by:
Combing IR & Ultrasound for Steam Trap Testing
In order to increase the accuracy of thermographic inspections of steam traps, contact ultrasonic testing should be used as well as infrared imaging. Contact ultrasonics are much more sensitive to trap failures than temperature measurement alone.
When testing traps, begin by using your thermal imager to ascertain that steam is reaching the trap. The trap inlet should be above 212 F. Next, listen to the trap outlet with your ultrasonic unit. Although traps should cycle periodically, you should not hear a continuous hissing or rushing sounds.
While it takes some practice to become proficient with ultrasonic testing, the increased accuracy is worth the effort.
September 30, 2002
Sponsored by:
Defining Ambient Temp
Ambient temperature is a term which appears in nearly all thermographic reports. However, many thermographers define ambient differently. Some define it as room air temperature while others define it as the temperature inside of the component enclosure.
According to the IEEE, for electrical components ambient temperature is the environmental temperature immediately surrounding the subject component. For devices located within enclosures, this is the temperature within the enclosure while it is closed and operating. For components in free air, it is the temperature surrounding the component.
October 07, 2002
Sponsored by:
Record Electrical Loads
When performing an electrical system inspection, don’t forget to record electrical load on the subject circuits. Doing so will not only enable you to duplicate your inspection efforts during a follow up inspection but will also allow you to make meaningful assessments when trending either absolute temperatures or delta Ts.
Ammeter readings should always be taken with a true RMS sensing ammeter for accurate load readings.
October 21, 2002
Sponsored by:
Why GFCI Devices Appear Warm
When performing an infrared inspection of an electrical panel you may notice that the phenolic bodies of Ground Fault Circuit Interrupters appear warm. This condition is usually due to the construction of the device itself.
In order to monitor the amount of current flowing through the supply and neutral conductors of a circuit, GFCI devices have small transformers built into them. These transformers can cause the body of the GFCI to run several degrees warmer than ambient temperature.
When inspecting GFCI devices, compare the thermal patterns of these devices to other similar devices under similar load. Be sure to inspect the load side connection at the GFCI device and the neutral bar connection as well.
October 28, 2002
Sponsored by:
Liquid filled Transformers
A thorough infrared inspection of an electrical transformer can point out symptoms of loose connections as well as other possible problems. When performing an infrared inspection of a liquid-filled transformer, be certain to include not only the primary and secondary connections but also the following items as well:
1) Inspect neutral and grounding connections for hot spots.
2) For transformers with separate tanks for each phase, compare phase tanks to each other. Transformers with balanced loads will exhibit similar temperatures between tanks.
3) Qualitatively inspect radiator section. Radiator tubes should be uniform in temperature and, in most cases, should operate above ambient temperature.
4) Compare transformer operating temperature to nameplate rating. For long term service, transformers should not operate above their maximum rated temperature.
5) Compare tap changer tank to main body of transformer. For properly operating tap changers, tap changer tank should not appear warmer than main body of transformer.
In conjunction with the infrared inspection, cooling fans and or pumps should be checked for proper settings and operation.
Finally, transformers require proper air circulation for cooling. To help ensure maximum airflow, transformer radiators should be unobstructed and free from dirt and debris.
November 04, 2002
Sponsored by:
Dry-type Transformers
A thorough infrared inspection of an electrical transformer can point out symptoms of loose connections as well as other possible problems. When performing an infrared inspection of a dry-type transformer, be certain to include not only the primary and secondary connections but also the following items as well:
1) Inspect neutral and grounding connections for hot spots.
2) Compare phase coils to each other. Transformers with balanced loads will exhibit similar temperatures between windings.
3) Compare each phase coil to itself. Properly operating coils should exhibit no pronounced hot or cold spots.
4) Inspect voltage tap jumper connections. Both connections should be the same temperature. In most cases, the jumper will be colder than the windings.
5) Compare transformer operating temperature to nameplate rating. For long term service, transformers should not operate above their maximum rated temperature.
In conjunction with the infrared inspection, cooling fans should be checked for proper settings and operation.
Finally, transformers require proper air circulation for cooling. To help ensure maximum airflow, transformer ventilation openings should be unobstructed and free from dirt.
November 11, 2002
Sponsored by:
Keeping Track of Your Lenses
If you have multiple imaging radiometers of the same make and model, it is imperative to keep your lenses with the imager for which they have been calibrated. Because each lens is individually calibrated to a specific imager, mixing up lenses from different cameras can cause serious inaccuracies when measuring temperatures.
The easiest way to keep track of your lenses is to mark each lens with the serial number of the camera to which it has been calibrated. This can be done by using a permanent marker or pressure sensitive label to apply the serial number to the body of the individual lenses.
It is recommended that lenses be marked upon recipt of the camera. Taking a few minutes to do this before you use your new equipment can prevent errors and embarassment in the future.
November 18, 2002
Sponsored by:
Infrared Equipment – New or Used?
Purchasing a pre-owned thermal imager can result in significant savings over the cost of a new unit. New thermal imagers that do not measure temperatures begin at approximately $13,000 US; new thermal imagers that do measure temperatures begin at under $20,000 US. Prices for both types of imagers increase with image resolution and features.
With the recent introduction of several new models of thermal imagers, there are several used pieces of equipment available from private sellers and manufacturers who have taken used equipment as trade-ins. Buying an imager from a private seller can be risky as no warranty is offered and you may not know how the equipment has been handled.
Purchasers of used equipment should be aware that there are no third party repair facilities for any infrared test equipment. Consequently, all equipment must be serviced by the company that manufactured the subject equipment. Furthermore, some thermal imagers are no longer being supported or serviced by the companies who manufactured them.
Purchasing used equipment from a manufacturer is generally less risky as many manufacturers do offer limited warranties and service for used equipment that they sell. Significant savings can often be realized by purchasing a sales demo units that usually become available once a manufacturer introduces a new model imager.
For more information on infrared equipment, please visit: www.irinfo.org
In order to avoid a costly error in your purchase, we strongly suggest potential buyers complete a Level 1 Certified Infrared Thermographer Course BEFORE they buy any equipment. Doing so will enable you to better acquaint yourself with the different types of cameras available, the applications and limitations of same, and how to accurately use this equipment in the field.
Because equipment varies widely in its capabilities, it is imperative that buyers and users of infrared test equipment fully understand how to properly choose an instrument for the task at hand.
Lastly, the greatest limiting factor in an infrared inspection is the equipment operator. Relying on data by untrained persons can have disastrous consequences. To this end, a trained and certified operator of infrared equipment is of paramount importance for accurate data collection and interpretation. For training and certification courses for thermographers, please visit our list of training companies.
November 25, 2002
Sponsored by:
Wide Angle Lenses
Using a standard lens to perform infrared inspections at close distances can be particularly difficult. This situation is quite common when inspecting motor control centers and some types of mechanical equipment.
If you must image from a near distance, you may not be able to compare your target to an adjacent reference. For larger targets you may be able to image only see a portion of the target.
Wide angle lenses increase an imagers visual field of view allowing a thermographer to image a wider target area without having to move farther from the target. Wide angle lenses are available for most imagers in multipliers of either 2x wide or 3x wide. Spot measurement size will increase proportionately to the width multiplier for the lens.
If you are taking temperatures, be sure that your wide angle lens has been calibrated for your imager.
December 02, 2002
Sponsored by:
Infrared Inspections of Building Envelopes
As winter rapidly approaches, many people are beginning to think about the upcoming heating season and the thermal performance of their homes and offices. Thermal imaging can be extremely useful in identifying areas of excessive heat loss or air leakage. The effectiveness of an infrared inspection will depend upon how the inspection is performed.
A common misconception is that infrared inspections are performed merely by looking at the exterior surfaces of a building from the outside of the structure. While this practice may identify gross defects for some structures, it usually fails to detect more serious defects such as air infiltration and heat distribution problems within the building.
For best results, infrared inspections of buildings should be performed from the inside of the building when there is a minimum inside/outside temperature differential of 10 Celsius (18 F) degrees for several hours prior to, and during the inspection. The inspection should include all exterior walls, windows, doors and ceilings imaged from the interior of the building. Performing the inspection on a calm night will eliminate errors due to solar loading and wind. Additionally, the building HVAC system should be operated under normal conditions. For commercial buildings this may involve overriding the HVAC system controls to duplicate daytime settings.
If you are concerned about the thermal performance of your building, the best time to conduct an infrared inspection is at the beginning of the heating season. Performing your inspection now will enable you to make necessary repairs before the coldest weather sets in.
As always, a certified, experienced thermographer will help to ensure that you receive accurate and reliable data.
December 09, 2002
Sponsored by:
Safety Standards for Thermography
Although thermography has gained wide acceptance for use in P/PM, Condition Monitoring and Forensics, thermographers often are unaware of the existence of published safety standards regarding infrared inspections.
The following is a partial list of currently distributed safety standards along with the organizations who publish them. Contact these organizations directly to obtain copies.
National Fire Protection Association, Quincy MA
NFPA 70E Standard For Electrical Safety Requirements for Employee
Workplaces
Occupational Safety and Health Administration
29 CFR Part 1910 Occupational Safety and Health Standards for General
Industry
29 CFR Part 1926 Occupational Safety and Health Standards for General
Construction
It should be noted that many workers (miners, transportation, many federal workers) are exempt from OSHA standards; however, there are often agencies similar to OSHA who publish applicable standards for these workers.
Infrared Inspections are often performed in hazardous environments. Safely conducting an infrared inspection should be of paramount importance for all involved. Prior to beginning an infrared inspection, a thermographer must be aware of which safety standards apply to his/her work.
The Infraspection Institute Level 3 Certified Infrared Thermographer covers thermographer safety and applicable standards in depth. For more information, contact Infraspection Institute at 609-239-4788 or online at www.infraspection.com.
December 16, 2002
Sponsored by:
Performance Standards
Performance Standards and Specifications for Thermography
Although thermography has gained wide acceptance for use in P/PM, Condition Monitoring and Forensics, thermographers often are unaware of the existence of published standards and specifications regarding infrared inspections.
The following is a partial list of currently distributed performance standards and specs along with the organizations who publish them. Contact these organizations directly to obtain copies.
- American Society for Testing and Materials, West Conshohocken, PA
- ASTM C 1060-97 Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
- ASTM C-1153-97 Practice for the Location of Wet Insulation in Roofing Systems Using Infrared Imaging
- ASTM E 1316-97 Terminology for Nondestructive Examinations
- ASTM E 1862-97 Standard Test Methods for Measuring and Compensating for Reflected Temperature Using Infrared Imaging Radiometers
- ASTM E 1933-97 Standard Test Methods for Measuring and Compensating for Emissivity Infrared Imaging Radiometers
- ASTM E 1934-97 Standard Guide for Examining Electrical and Mechanical Equipment with Infrared Thermography
- Infraspection Institute, Burlington, NJ
- Guidelines for Infrared Inspection of Building Envelopes and Insulated Roofs
- Guideline for Measuring Distance/Target Size Values for Quantitative Thermal Imaging Cameras
- Guideline for Measuring and Compensating for Reflected Temperature, Emittance and Transmittance
- Guidelines for Infrared Inspection of Electrical and Mechanical Systems
- International Electrical Testing Association, Morrison, CO
- Acceptance Testing Specifications for Electrical Power Distribution Equipment and Systems
- Maintenance Testing Specifications for Electrical Power Distribution Equipment and Systems
- National Fire Protection Association, Quincy MA
- NFPA 70B Recommended Practice for Electrical Equipment Maintenance
Proper conduct of an infrared inspection and interpretation of data require thorough training and certification by a recognized training agency. For more information on training and certification, contact Infraspection Institute at 609-239-4788 or online at www.infraspection.com
December 23, 2002
Sponsored by:
Inspecting Retrofitted Roofs
If your roof has been retrofitted with a new roof installed over an existing one, it is imperative that you test the roofing system for water infiltration at least annually. With limited opportunity for egress, water entering the upper roof of a retrofitted system can cause widespread damage in a very short period of time. To make matters worse, there is usually no visual evidence of this type of a leak from inside of the building.
Performed in conjunction with regular visual inspections of your roof, infrared inspections of low slope roofs are a very cost effective way of tracking the overall health of your facility’s roofing system. Locating leaking areas while they are small allows them to be addressed before they can spread. Additionally, moisture trapped within a roofing system almost never dries out and can cause premature failure of roofing felts, adhesives, fasteners, and the roof deck.
Whether you choose to have an in-house thermography team or an outside contractor perform the inspection, make certain that the Thermographer is Certified and experienced. Since an infrared imager cannot confirm moisture presence, all infrared data must be verified by invasive testing as well.